PrecisionPro™ — Carve Factory-Sharp 45° Tile Miters Without a Wet Saw
High Quality
Free US Shipping
Easy 30 day Returns
Almost out of stock
Cut Factory-Sharp 45° Tile Miters Without Renting a Wet Saw
Stop chipping $14 porcelain tiles every time the blade catches. The PrecisionPro™ Tile Chamfer Stand locks your Type 100 angle grinder into a fixed 45° track so the diamond blade does the work — not your wrist. Built-in water cooling, four-knob bed adjustment, and a stainless-steel cradle that holds true cut after cut.
Stop Ruining Tiles On Wavy, Chipped Freehand Miters
You know the routine. The grinder wobbles, the blade binds halfway through, and the porcelain face fractures right where everyone will see it. Renting a wet saw runs $80–$120 a day. A cheap manual tile cutter handles 90° splits and won't touch a 45° miter. So you keep cutting freehand — and keep wasting tiles.
➤ Locked 45° track kills the wobble: The cradle pins your grinder at a true 45° while the steel bed runs the tile flat underneath — no drift, no chatter, no wavy lines on the finish edge.
➤ Push-fit water cooling fights chipping: A built-in water-line connector feeds a steady drip onto the blade as it cuts — knocks down dust, cools the diamond, and keeps the porcelain face chip-free.
➤ Four-knob bed handles every tile thickness: Twist the locking knobs to slide the bed under your blade for tiles up to 15mm thick — wall tile, floor tile, stone slab, same setup, no swapping jigs.
How The PrecisionLock™ Cradle Delivers Factory-Edge Miters
Most chipping happens at the exit of the cut. When the blade leaves the tile freehand, the porcelain face fractures because the disc tilts a fraction of a degree at the worst possible moment. The PrecisionLock™ cradle eliminates that tilt — your grinder housing sits in a steel collar that won't budge while the tile slides flat along the bed below.
Add the push-fit water line and the diamond stays cool through every pass, so the blade doesn't glaze and the cut edge stays crisp. That's the difference between "looks DIY" and "looks like the tile shop did it."
Why DIY Renovators Skip The Wet-Saw Rental Now
Once you've cut a tight 45° on real porcelain with this stand, fighting the grinder freehand feels like punishment. Renovators, weekend tilers, and small-job contractors keep reporting the same thing — faster setup than dragging a wet saw home, less mess, and miters that fit factory-tight when grouted.
"I chipped two porcelain tiles freehand before this showed up. Once I locked it in I cut sixteen miters in a row — every one tight enough to grout in a 1mm line. Wish I'd ordered it before I started the bathroom." — Marcus T.
Cut Tiles Like A Tile Shop, Not Like A First Timer
✓ Tight-fitting miters every time: Lock the bed, slide the tile, get a chip-free 45° edge that grouts up to a clean 1–2mm line on outside corners.
✓ Works on porcelain, ceramic, and stone: Same setup handles wall tile, floor tile, and stone slabs up to 15mm — no need for separate jigs.
✓ Built to outlast one bathroom: Heavy-gauge stainless platform and reinforced metal cradle hold true cut after cut — won't flex out of square halfway through the job.
Set Up In Under 90 Seconds, Then Just Cut
Step 1: Drop your Type 100 angle grinder into the steel cradle — fits gearboxes up to 4.5cm (1.77") across — and tighten the PrecisionLock™ collar.
Step 2: Twist the four bed knobs to match your tile thickness, then snap a standard water line into the push-fit connector for cooling and dust suppression.
Step 3: Power up, feed the tile flat along the bed, and let the locked 45° track do the work — every miter comes out the same.
| What You Need | PrecisionPro™ Stand | Handheld Cutting |
|---|---|---|
| Chip-free 45° miters | ✅ Locked bed, every cut | ❌ Wavy, chipped edges |
| Water cooling for porcelain | ✅ Push-fit hose connector | ❌ Dry-cut dust and glazing |
| Holds true cut after cut | ✅ Stainless cradle, won't flex | ❌ Wrist fatigue, drift |
Technical Specs Made Simple
- Fits Your Grinder: Type 100 angle grinders with gearbox/neck diameter up to 4.5cm (1.77")
- Material: Heavy-gauge stainless steel platform with reinforced metal cradle
- Cut Angle: Locked 45° for chip-free chamfer miters
- Tile Thickness: Adjustable bed handles tiles up to 15mm
- Base Dimensions: 13.5cm (W) × 30cm (L)
- Water Cooling: Push-fit connector for standard water-line tubing
- Includes: 1× PrecisionPro™ Tile Chamfer Stand
Got Questions? We've Got You Covered
Will this fit my angle grinder?
If your grinder is a Type 100 (4" / 100mm) with a gearbox neck up to 4.5cm (1.77") across, it drops straight in. Most popular brands — DeWalt, Makita, Bosch, Milwaukee — fit. Measure the round housing behind the disc guard if you're unsure.
Does the water cooling actually do anything?
Yes — and it matters most on dense porcelain. A wet blade runs cooler, won't glaze, and exits the cut without fracturing the tile face. It also kills 80%+ of the dust cloud you'd get dry-cutting.
How thick of tile can it handle?
The bed adjusts for tiles up to 15mm thick — covers everything from standard 8mm wall tile through 12mm floor porcelain to thicker stone. Twist the four locking knobs to slide the bed under your blade.
Is the metal real or thin stamped junk?
Real stainless platform, reinforced cradle, and steel hardware. It's built to handle a full bathroom or kitchen run without flexing out of square — not a one-project tool.
Does the package include the angle grinder?
No — the package is the PrecisionPro™ Tile Chamfer Stand only. You'll need your own Type 100 angle grinder and a diamond cutting/grinding blade rated for tile.
Built For Tilers Who Want Tile-Shop Edges Without The Tile-Shop Bill
If your PrecisionPro™ stand doesn't deliver chip-free 45° miters straight out of the box, send it back for a full refund — no restocking, no questions. Cut the cleanest miters of your renovation, or you don't pay for the tool.
What our customers have to say:
Arvilaro Guarantees
Rated 4.6 / 5 based on 1289 reviews. Showing our 4 and 5-star reviews.